Getting started with STM MCUs: STM32F469 Evalboard

STM32F469 Evalboard (STM32469I-EVAL).

The following article explains all necessary steps to create an Embedded Wizard UI application suitable for the STM32F469 Evalboard. Please follow these instructions carefully and step by step in order to ensure that you will get everything up and running on your target. In case you are not familiar with Embedded Wizard, please read first the Quick Tour tutorial to understand the principles of Embedded Wizard and the GUI development workflow.

Prerequisites

First of all, you need the following hardware components:

STM32F469 Evalboard from STMicroelectronics (STM32469I-EVAL)

USB cable to connect the board with your PC

Serial cable to connect the USART port of the board with your PC

Make sure that you have got the following software packages:

Embedded Wizard Studio Free or Embedded Wizard Studio Pro

Embedded Wizard STM32 Platform Package

Embedded Wizard Build Environment for STM32F469 Evalboard

TIP

If you want to use the Free edition of Embedded Wizard Studio and the STM32 Platform Package, please register on our website and select the target STM32F469 Evalboard. Then you can download the above software packages.

All customers who licensed Embedded Wizard can visit our download center to get the above software packages.

Installing Tools and Software

Step 1: Install the latest version of Embedded Wizard Studio.

Step 2: Install the Embedded Wizard STM32 Platform Package.

Step 3: Download the STM32CubeProgrammer and install it. Test the connection from PC to Evalboard and the proper installation of the USB drivers: Connect the Evalboard with your PC via USB (make sure to use the ST-LINK USB connector) and start the previously installed STM32CubeProgrammer. Select the green button Connect and verify that the connection could be established successfully. Finally, close the STM32CubeProgrammer utility.

Step 4: Unpack the provided Embedded Wizard Build Environment for STM32F469 Evalboard to your local file system (e.g. C:\STM32\STM32F469-Evalboard).

Step 5: Take a text editor and open the file FlashDownload.cfg that you will find in the subdirectory \Application\FlashDownload of the Build Environment. At the beginning of the file, the following environment variable has to be set to the installation path of the STM32CubeProgrammer utility:

Stm32CubeProgrammerPath - Absolute path of your installed STM32CubeProgrammer utility (Step 3).

Embedded Wizard GUI Demos

If you just want to run our GUI demos on your STM32F469 Evalboard without building the different examples, you can simply flash the binary file of the Embedded Wizard Master Demo.

The Embedded Wizard Master Demo combines a variety of examples within one huge demo application. It can be used for presentations and showcases. Each demo application can be activated from a common main menu. To return back from a demo application to the main menu, a small home button appears on top of every demo. Additionally, the Master Demo contains an auto-demo mode that presents one demo application after the other. The auto-demo starts automatically and stops as soon as the user touches the screen.

In order to flash the binary file to your target, please follow these steps:

Connect your development board with your PC via USB (make sure to use the ST-LINK USB connector).

Execute the batch file FlashMasterDemo.bat: A console window will appear and the flash tool will download the binary file of the Master Demo.

'Master Demo' running on STM32F469 Evalboard.

Exploring the Build Environment

The provided Embedded Wizard Build Environment for STM32F469 Evalboard contains everything you need to create, compile, link and flash an Embedded Wizard UI application for the STM32F469 target. After unpacking, you will find the following subdirectories and files:

StartGccBuildEnvironment.bat - This script file is provided to start a windows command line to build your GUI applications for the target.

\Application - This folder contains ready-to-use projects to compile and link an Embedded Wizard generated UI application. They are used for all provided examples and they can be used to build your own UI applications.

\FlashDownload - This folder contains a script to load the created binaries into the flash of your target by using the STM32CubeProgrammer tool. Don't forget to set the path of your installed STM32CubeProgrammer utility within the file FlashDownload.cfg.

\GeneratedCode - This folder is used to receive the generated code from an Embedded Wizard UI project. All template projects are building the UI application out of this folder. You can create your own UI project and generate the code into the subdirectory \GeneratedCode without the need to adapt the project.

\Project - This folder contains the prepared projects for GCC (make), IAR Embedded Workbench, Keil MDK-ARM and STM32CubeIDE.

\Source - This folder contains the files main.c and ewmain.c. There you will find the initialization of the system and the main loop to drive an Embedded Wizard GUI application. The file ewconfig.h contains general configuration settings for the target system, like memory ranges and display parameter and configuration settings for the Embedded Wizard Graphics Engine and Runtime Environment. Additionally, this folder contains a configuration file for FreeRTOS and the device driver C/H files used for the DeviceIntegration example.

\Examples - This folder contains a set of demo applications. Each example is stored in a separate folder containing the entire Embedded Wizard UI project. Every project contains the necessary profile settings for the STM32F469 target. The following samples are provided:

\HelloWorld - A very simple project that is useful as starting point and to verify that the entire toolchain, your installation and your board is properly working.

\ColorFormats - This project demonstrates that every UI application can be generated for different color formats: RGBA8888, RGB888, RGBA4444, RGB565, Index8 and LumA44.

\ScreenOrientation - This demo shows, that the orientation of the UI application is independent from the physical orientation of the display.

\DeviceIntegration - This example shows the integration of devices into a UI application and addresses typical questions: How to start a certain action on the target? How to get data from a device?

\GraphicsAccelerator - This application demonstrates the graphics performance of the DMA2D hardware graphics accelerator. Sets of basic drawing operations are executed permanently and continuously, while the user can switch on/off the hardware accelerator.

\BezierClock - The sample application BezierClock implements a fancy digital clock and timer application with animated digits. The application uses vector graphics to render dynamically the different digits for clock and timer. The change from one digit to another is handled by moving the vector points to get a smooth transition animation.

\BrickGame - The sample application BrickGame implements a classic "paddle and ball" game. In the game, a couple of brick rows are arranged in the upper part of the screen. A ball travels across the screen, bouncing off the top and side walls of the screen. When a brick is hit, the ball bounces away and the brick is destroyed. The player has a movable paddle to bounce the ball upward, keeping it in play.

\ChartsDemo - This application demonstrates the possibilities and the usage of the chart classes LineChart, BarChart and PieChart. The appearance of each chart diagram can be configured easily by using their corresponding properties. Additionally, this demo shows the usage of an outline box to manage scrollable content.

\ClimateCabinet - The ClimateCabinet demo shows the implementation of a control panel for a climatic exposure test cabinet. The user can define a heating time, a nominal temperature and humidity, a dwell time and the final cooling time.

\Dashboard - The sample application Dashboard shows the implementation of a car dashboard. The application demonstrates the usage of vector graphics created from svg path data and how transitions between two dashboard variants and further UI components can be achieved.

\PaperCutter - This demo shows the implementation of a paper cutting machine, where the user can define the pagination and format of the paper as well as the cutting speed and the amount of papers. The application contains many rect effects and fade-in/fade-out effects to change dynamically the layout of the screen.

\PulseOximeter - The sample application PulseOximeter shows the implementation of a medical device for monitoring a person's pulse frequency and peripheral oxygen saturation. The application demonstrates the usage of vector graphics within graphs and circular gauges.

\SmartThermostat - The SmartThermostat demo application shows the implementation of a fancy, rotatable temperature controller to adjust and display the nominal and actual temperature.

\WashingMachine - This demo shows the implementation of a washing machine with a couple of fancy scrollable list widgets to choose the washing program and parameters. The speciality of this sample application is the magnification effect of the centered list items and the soft fade-in/fade-out effects.

\WaveformGenerator - This WaveformGenerator demo application combines waveforms with different amplitudes and frequencies. The implementation shows the usage of vector graphics to draw a curve based on a list of coordinates.

\MasterDemo - This folder contains the binary file of the Embedded Wizard Master Demo application and a script file to flash the demo on your target. The Master Demo combines a variety of examples within one huge demo application. It can be used for presentations and showcases.

\PlatformPackage - This folder contains the necessary source codes and/or libraries of the STM32 Platform Package: Several Graphics Engines for the different color formats (RGBA8888, RGB888, RGBA4444, RGB565, Index8 and LumA44) and the Runtime Environment (in the subdirectory \RTE).

\TargetSpecific - This folder contains all configuration files and platform specific source codes. The different ew_bsp_xxx files implement the bridge between the Embedded Wizard UI application and the underlying board support package (STM32 hardware drivers) in order to access the display, the graphics accelerator, the serial interface and the clock.

\ThirdParty - This folder contains third-party source codes and tools:

\gcc-arm-none-eabi - This folder contains a subset of the GCC ARM embedded toolchain to compile the examples.

\Make - This folder contains a make tool to build the entire GUI application via command line.

\STM32Cube_FW_F4 - This folder contains the necessary subset of the STM32CubeF4 embedded software for STM32F4 series used for the Embedded Wizard UI applications (HAL, BSP, drivers, FreeRTOS).

Creating the UI Examples

For the first bring up of your system, we recommend to use the example 'HelloWorld':

Example 'HelloWorld' within Embedded Wizard Studio.

The following steps are necessary to generate the source code of this sample application:

Navigate to the directory \Examples\HelloWorld.

Open the project file HelloWorld.ewp with your previously installed Embedded Wizard Studio. The entire project is well documented inline. You can run the UI application within the Prototyper by pressing Ctrl+F5.

To start the code generator, select the menu items BuildBuild this profile - or simply press F8. Embedded Wizard Studio generates now the sources files of the example project into the directory \Application\GeneratedCode.

Compiling, Linking and Flashing

The following steps are necessary to build and flash the Embedded Wizard UI sample application using the GCC ARM embedded toolchain:

Navigate to the top level of the Build Environment.

Open StartGccBuildEnvironment.bat - as a result, a windows command line window should open. In case there are error messages, please edit the file and double-check the path settings.

Now start compiling, linking and flashing:

make make install

If everything works as expected, the application should be built and flashed to the STM32F469 target.

Example 'HelloWorld' running on STM32F469 Evalboard.

All other examples can be created in the same way: Just open the desired example with Embedded Wizard Studio, generate code and rebuild the whole application using simply:

make install

Creating your own UI Applications

In order to create your own UI project suitable for the STM32F469 target, you can create a new project and select the STM32F469 Evalboard project template:

As a result you get a new Embedded Wizard project, that contains the necessary Profile attributes suitable for the STM32F469 Evalboard:

The following profile settings are important for your target:

The attribute PlatformPackage should refer to an installed STM32 Platform Package.

The attribute ScreenSize should correspond to the display size of the STM32F469 Evalboard.

The attributes ModeOfBitmapResources and ModeOfStringConstants can be set to DirectAccess in case that the resources should be taken directly from flash memory. By default these attributes are set to Compressed.

The attribute OutputDirectory should refer to the \Application\GeneratedCode directory within your Build Environment. By using this template, it will be very easy to build the UI project for your target.

The attribute CleanOutputDirectories should be set to true to ensure that unused source code within the output directory \Application\GeneratedCode will be deleted.

The attribute PostProcess should refer to \Application\Project\EWARM\EWARM_ew_post_process.cmd if you are working with IAR Embedded Workbench or to \Application\Project\MDK-ARM\MDK-ARM_ew_post_process.cmd if you are working with Keil MDK-ARM or to \Application\Project\STM32CubeIDE\STM32F469-Evalboard\STM32CubeIDE_ew_post_process.cmd if you are working with STM32CubeIDE. In case of the GCC ARM embedded toolchain leave it blank

Now you can use the template project in the same manner as it was used for the provided examples to compile, link and flash the binary.

After generating code, please follow these steps, in order to build your own UI application:

Start the batch file 'StartGccBuildEnvironment.bat'. Again, a windows command line window should open.

Start compiling, linking and flashing:

make install

Most of the project settings are taken directly out of the generated code, like the color format or the screen orientation. Only a few additional settings can be configured directly within the Makefile, like the usage of an external flash memory or the usage of the FreeRTOS operating system.

Console output

In order to receive error messages or to display simple debug or trace messages from your Embedded Wizard UI application, a serial terminal like 'Putty' or 'TeraTerm' should be used.

Connect the USART port of your STM32F469 Evalboard with the PC via serial connection. Open the device manager to get the number of the installed COM port.

Now you can open your terminal application and connect it via COMx with the following settings: 115200-8-N-1

This terminal connection can be used for all trace statements from your Embedded Wizard UI applications or for all debug messages from your C code.

Using IAR Embedded Workbench

If you want to use the IAR Embedded Workbench instead of the GCC ARM embedded toolchain, please follow these instructions:

TIP

By default, the external QSPI flash of the STM32 board is used to store string constants, bitmap resources and font resources.

If the flash downloader integrated in IAR Embedded Workbench doesn't support the external flash, the examples can alternatively be flashed using the STM32CubeProgrammer. For more convenience the STM32CubeProgrammer can be integrated to IAR Embedded Workbench as an external tool.

Command and argument are as follows:

$PROJ_DIR$\..\..\FlashDownload\FlashDownload.cmd

$TARGET_PATH$ separateConsole

The subdirectory \Application\Project\EWARM contains a template project that is commonly used for all provided Embedded Wizard examples. All Embedded Wizard examples will store the generated code within the common \Application\GeneratedCode folder.

The generated code of an Embedded Wizard example is imported automatically to the IAR Embedded Workbench project using the Project Connection mechanism.

To establish this automatic project import a post process has to be added to the Profile settings within Embedded Wizard Studio:

Open the desired Embedded Wizard example project.

Select the Profile and set the attribute PostProcess to the file ..\..\Application\Project\EWARM\EWARM_ew_post_process.cmd.

After the Embedded Wizard code generation the installed post process will generate a ewfiles.ipcf file, that controls the import to the IAR Embedded Workbench project.

After returning to IAR Embedded Workbench, the latest generated code and the suitable Embedded Wizard Platform Package will be imported to the IAR Embedded Workbench project (depending on the color format and the screen orientation selected in the Embedded Wizard Profile).

If the color format or the screen orientation was changed, please do a complete rebuild of the IAR Embedded Workbench project.

Using Keil MDK-ARM

If you want to use the Keil MDK-ARM toolchain instead of the GCC ARM embedded toolchain, please follow these instructions:

The subdirectory \Application\Project\MDK-ARM contains a template project that is commonly used for all provided Embedded Wizard examples. All Embedded Wizard examples will store the generated code within the common \Application\GeneratedCode folder.

The generated code of an Embedded Wizard example is imported automatically to the Keil MDK-ARM project using the CMSIS PACK mechanism.

The following steps are needed to establish this automatic project import:

Install Tara.Embedded_Wizard_Launcher.x.x.x.pack by double clicking. You will find the file within the subdirectory \Application\Project\MDK-ARM.

Open the desired Embedded Wizard example project.

Select the Profile and set the attribute PostProcess to the file ..\..\Application\Project\MDK-ARM\MDK-ARM_ew_post_process.cmd.

After the Embedded Wizard code generation the installed post process will generate a ewfiles.gpdsc file, that controls the Keil MDK-ARM project import.

In Keil MDK-ARM a dialog appears: "For the current project new generated code is available for import". After confirmation, the latest generated code and the suitable Embedded Wizard Platform Package will be imported to the Keil MDK-ARM project (depending on the color format and the screen orientation selected in the Embedded Wizard Profile).

If the color format or the screen orientation was changed, please do a complete rebuild of the Keil MDK-ARM project.

Using STM32CubeIDE

If you want to use the STM32CubeIDE toolchain instead of the GCC ARM embedded toolchain, please follow these instructions:

The subdirectory \Application\Project\STM32CubeIDE contains a template project that is commonly used for all provided Embedded Wizard examples. All Embedded Wizard examples will store the generated code within the common \Application\GeneratedCode folder.

The following steps are needed to establish this automatic project import:

Open the desired Embedded Wizard example project.

Select the Profile and set the attribute PostProcess to the file ..\..\Application\Project\STM32CubeIDE\STM32F469-Evalboard\STM32CubeIDE_ew_post_process.cmd.

After the Embedded Wizard code generation the installed post process will adapt the .cproject XML file. All necessary libraries and include paths (depending on the color format and screen rotation) will be set automatically.

The given STM32CubeIDE example under \Application\STM32CubeIDE contains a workspace which has all adaptions for an Embedded Wizard project. For using this within STM32CubeIDE do following steps:

Open STM32CubeIDE and select the directory \Application\Project\STM32CubeIDE as workspace directory.

To import the C project, select the menu item FileImport and choose General - Existing Projects into Workspace and press Next.

Choose Select root directory - Browse and select the directory \Application\Project\STM32CubeIDE\STM32F469-Evalboard.

Press Finish.

To compile the project press the Build button (hammer symbol) within the toolbar.

Press the Run or Debug button within the toolbar to start the application on the target.

If the color format or the screen orientation was changed, please do a clean in STM32CubeIDE.

Custom specific hardware

In order to bring-up an Embedded Wizard generated UI application on your STM32 custom hardware, you can use the provided Embedded Wizard Build Environment for STM32F469 Evalboard as a template. The subdirectory \TargetSpecific contains all configuration files and platform specific source codes. Assuming that your custom hardware is similar to the STM32F469 Evalboard, the following adaptations or configurations are typically necessary:

System clock (ew_bsp_system.c) - The first and the important step is to configure the system and peripheral clock. Depending on your hardware you can use the internal or external clock as source. Please take care that your LTDC and USART are connected to the selected clock source and configured correctly. The Embedded Wizard UI application runs independent from the chosen system frequency, however, with a slow system clock, all components need more time for their tasks (e.g. display refresh).

SDRAM (ew_bsp_system.c) - The SDRAM configuration has to be adapted to your particular SDRAM. Please use a memory test to ensure that writing and reading works properly. If the start address and/or the size of the SDRAM has changed, please adapt the settings for the framebuffer and the memory pool within the file ewconfig.h.

USART (ew_bsp_console.c) - Typically, the USART configuration just requires a new pinout according your hardware layout. The usage of the serial connection is highly recommended in order to get status and debug messages during runtime.

LTDC and DSI (ew_bsp_display.c) - The LTDC is an integrate display controller which allows you to connect many different display types to a STM32 device. In case of STM32F469 Evalboard, the MIPI-DSI is used as interface to the display. In case you are not using a MIPI-DSI display, please use the Build Environment for STM32F429-Evalboard as template.

Touch (ew_bsp_touch.c) - If your application requires touch support, you can integrate a given touch driver provided by the touch controller manufacturer or write your own. As a result the current touch position should be returned.

As soon as these steps are done, you can create your own GUI application or use one of the provided examples. If the size of your display is different compared to the display of the STM32F469 Evalboard (800x480 pixel), please adapt the attribute ScreenSize of the UI project and the size of the framebuffer within the file ewconfig.h accordingly.

Release notes

The following section contains the version history of the Build Environment (including Graphics Engine and Runtime Environment) for STM32F469 Evalboard. These release notes describe only the platform specific aspects - for all general improvements and enhancements please see the Embedded Wizard release notes.

Version 11.00

Flash download: Flashing the binary to the target is now controlled by one dedicated script that is used from the makefile and the other toolchains. The script is located in the subdirectory \Application\FlashDownload. The settings can be changed within the file FlashDownload.cfg.

Linker section definitions: The linker section definitions for constant data can now be done directly within the file ewconfig.h. The set of defines have been enhanced to control the location of all types of constant data. The following defines are supported: EW_USE_EXTERNAL_FLASH, EW_BITMAP_PIXEL_SECTION_NAME, EW_FONT_PIXEL_SECTION_NAME, EW_FONT_DATA_SECTION_NAME, EW_CONST_STRING_SECTION_NAME.

Touch configuration and calibration: The file ewconfig.h contains now a set of defines to print and calibrate the touch events from the touch device.

The functions EwBspDisplayInit() and EwBspTouchInit() have been enhanced to use the size of the GUI application and display parameters.

Code size reduction: A set of new macros wtihin the file ewconfig.h are introduced to reduce the code size of the binary application: EW_DONT_USE_GRADIENTS, EW_DONT_USE_COMPRESSION, EW_DONT_USE_NATIVE_SURFACES, EW_DONT_USE_NATIVE_SURFACES_AS_DESTINATION.

All macros within the file ewconfig.h concerning framebuffer width/height/address/size, double-buffer width/height/addresss/size, color depths, etc. have been renamed with a leading EW_ to be in line with other macros.

Changed to STM32CubeF4 Firmware Package V1.26.0.

Changed to GCC ARM Embedded Toolchain 10-2020-q4-major.

Version 11.00.01

Downgrade of GCC ARM embedded toolchain from 10-2020-q4-major back to 9-2020-q2-update used for building the binary. In some cases the dependency files that are created during compilation contain erroneous path entries. As a result the next make fails with 'no rule to make target C\:\STM32'.

Version 11.00.02

Changed to STM32CubeProgrammer V2.10.0.

Prepared FlashDownload.cmd file to work with STM32CubeProgrammer V2.10.0.